| |
|
 |
相关文章 |
 |
|
|
|
|
 |
思科认证考试（ＣＣＮＡ）考试模拟题６０—７１及答案(1) |
|
|
| 思科认证考试（ＣＣＮＡ）考试模拟题６０—７１及答案(1) |
|
作者：佚名 文章来源：不详更新时间：2006-5-30 8:37:18  |
|
Questions
60. [RINx] What condition does Serial 0 down & protocol up represent?
a) The interface is disconnected but keep alives are being received
b) The interface is working properly but keep alives are not being received
c) The interface is bad and should be replaced
d) The interface is working correctly.
e) Condition not possible
61.[CxNx] What command correctly displays the running configuration file?
a) show configuration
b) show running-configuration
c) show active-configuration file
d) write terminal
e) all of the above
62. [RINx] What is the purpose of TTL?
a) Prevent routing loops
b) Prevents Timely Telnet Losses
c) Remind engineers that life is short
d) To prevent IP datagrams from living long and fruitful lives
e) To prevent IP datagrams that are caught in a routing loop from traversing the network forever.
63. [RINx] Which should be the subnet mask for a class C address if 62 hosts are required?
a) 255.255.255. 192
b) 255.255.192.0
c) 0.0.0.192
d) 255.255.255.62
e) none of the above
64. [CxNx] After the configuration command is used, when does it become effective?
a) immediately
b) after the router is rebooted
c) after you exit the configuration mode
d) depends on the change that is made
e) All of the above
65. [RxNx] Which one of the following is true concerning IPX load balancing?
a) Activated by default
b) Must be configured
c) IPX does not load balance
d) Requires a Novell File Server
e) None of the above
66. [BxNx] What is the purpose of spanning tree?
a) Prevents bridging loops
b) Prevents routing loops
c) Cisco supported feature that can be used per VLAN
d) Can be initiated on any routed interface
e) All of the above
Questions 67 - 71 refer to the following diagram and information.
The above figure represents a frame-relay network with PVC’s configured for a hub and spoke design with corresponding DLCI numbers. Assume all connections are with the serial 0 interface. Please refer to the above figure for questions 67-71.
67. [FINx] Given the following configuration for Router A:
Router_a(config)#interface s0
Router_a(config-if)#encapsulation
frame-relay
Router_a(config-if)#frame-
共11页: 1 [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] 下一页
relay
lmi-type ansi
Router_a(config-if)#frame-relay map ip
172.16.1.2 100
Router_a(config-if)#frame-relay map ip
172.16.1.3 101
Router_a(config-if)#frame-relay map ip
172.16.1.4 102
Router_a(config-if)#frame-relay map ip
172.16.1.5 103
Router_a(config-if)#frame-relay map ip
172.16.1.6 104
Router_a(config-if)#ip address
172.16.1.1 255.255.255.0
Which of the following is the proper configuration
for Router F?
a)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay
Router_f(config-if)#frame-relay
lmi-type ansi
b)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay
Router_f(config-if)#frame-relay
lmi-type ansi
Router_f(config-if)#ip address
172.16.1.6 255.255.255.0
c)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay
Router_f(config-if)#frame-relay
lmi-type ansi
Router_f(config-if)#ip address
172.16.1.6 255.255.255.0
Router_f(config-if)#frame-relay
map ip 172.16.1.1 104
d)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay
Router_f(config-if)#frame-relay
lmi-type ansi
Router_f(config-if)#ip address
172.16.1.6 255.255.255.0
Router_f(config-if)#frame-relay
map ip 172.16.1.1 604
e)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay
Router_f(config-if)#frame-relay
lmi-type ansi
Router_f(config-if)#ip address
172.16.1.6 255.255.255.0
Router_f(config-if)#frame-relay
map ip 172.16.1.6 604
68. [FINx] Given the following configuration for Router A:
Router_a(config)#interface s0
Router_a(config-if)#encapsulation
frame-relay ietf
Router_a(config-if)#frame-relay
map ip 172.16.1.2 100
Router_a(config-if)#frame-relay
map ip 172.16.1.3 101
Router_a(config-if)#frame-relay
map ip 172.16.1.4 102
Router_a(config-if)#frame-relay
map ip 172.16.1.5 103
Router_a(config-if)#frame-relay
map ip 172.16.1.6 104
Router_a(config-if)#ip address
172.16.1.1 255.255.255.0
Which of the following is the proper configuration for Router
共11页: 上一页 [1] 2 [3] [4] [5] [6] [7] [8] [9] [10] [11] 下一页
F?
a)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay
Router_f(config-if)#frame-relay
lmi-type ansi
b)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay
Router_f(config-if)#frame-relay
lmi-type ansi
Router_f(config-if)#ip address
172.16.1.6 255.255.255.0
Router_f(config-if)#frame-relay
map ip 172.16.1.1 104
c)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay
Router_f(config-if)#frame-relay
lmi-type cisco
Router_f(config-if)#ip address
172.16.1.6 255.255.255.0
Router_f(config-if)#frame-relay
map ip 172.16.1.1 104
d)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay
Router_f(config-if)#frame-relay
lmi-type cisco
Router_f(config-if)#ip address
172.16.1.6 255.255.255.0
Router_f(config-if)#frame-relay
map ip 172.16.1.1 604
e) None of the above.
69. [FINx] Given the following configuration for Router A:
Router_a(config)#interface s0
Router_a(config-if)#encapsulation
frame-relay ietf
Router_a(config-if)#frame-relay
lmi-type ansi
Router_a(config-if)#frame-relay
map ip 172.16.1.2 100
Router_a(config-if)#frame-relay
map ip 172.16.1.3 101
Router_a(config-if)#frame-relay
map ip 172.16.1.4 102
Router_a(config-if)#frame-relay
map ip 172.16.1.5 103
Router_a(config-if)#frame-relay
map ip 172.16.1.6 104
Router_a(config-if)#ip address
172.16.1.1 255.255.255.0
Which of the following is the proper configuration for Router F?
a)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay
Router_f(config-if)#frame-relay
lmi-type ansi
Router_f(config-if)#ip address
172.16.1.6 255.255.255.0
Router_f(config-if)#frame-relay
map ip 172.16.1.1 104
b)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay
Router_f(config-if)#frame-relay
lmi-type ansi
Router_f(config-if)#ip address
172.16.1.6 255.255.255.0
Router_f(config-if)#frame-relay
map ip 172.16.1.1 104 ietf
c)
Router_f(co
共11页: 上一页 [1] [2] 3 [4] [5] [6] [7] [8] [9] [10] [11] 下一页
nfig)#interface s0
Router_f(config-if)#encapsulation
frame-relay
Router_f(config-if)#frame-relay
lmi-type ansi
Router_f(config-if)#ip address
172.16.1.6 255.255.255.0
Router_f(config-if)#frame-relay
map ip 172.16.1.1 604
d)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay
Router_f(config-if)#frame-relay
lmi-type ansi
Router_f(config-if)#ip address
172.16.1.6 255.255.255.0
Router_f(config-if)#frame-relay
map ip 172.16.1.1 604 ietf
e)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay ietf
Router_f(config-if)#frame-relay
lmi-type ansi
Router_f(config-if)#ip address
172.16.1.6 255.255.255.0
Router_f(config-if)#frame-relay
map ip 172.16.1.1 104
70. [FINx] Given the following configuration for Router A:
Router_a(config)#interface s0
Router_a(config-if)#encapsulation
frame-relay
Router_a(config-if)#frame-relay
lmi-type cisco
Router_a(config-if)#frame-relay
map ip 172.16.1.2 100 ietf
Router_a(config-if)#frame-relay
map ip 172.16.1.3 101 ietf
Router_a(config-if)#frame-relay
map ip 172.16.1.4 102 ietf
Router_a(config-if)#frame-relay
map ip 172.16.1.5 103 ietf
Router_a(config-if)#frame-relay
map ip 172.16.1.6 104 ietf
Router_a(config-if)#ip address
172.16.1.1 255.255.255.0
Which of the following is the proper configuration for Router F?
a)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay ietf
Router_f(config-if)#frame-relay
lmi-type ansi
Router_f(config-if)#ip address
172.16.1.6 255.255.255.0
Router_f(config-if)#frame-relay
map ip 172.16.1.1 604
b)
Router_f(config)#interface s0
Router_f(config-if)#encapsulation
frame-relay
Router_f(config-if)#frame-relay
lmi-type [1] [2] [3] 下一页
|
|
| 文章录入：admin 责任编辑：admin |
| |
|
上一篇文章： CCNA专业英文词汇全集(1)(1)
下一篇文章： 思科认证考试（ＣＣＮＡ）考试模拟题７２—７８及答案(1) |
|
|
| 【字体：小 大】【发表评论】【加入收藏】【告诉好友】【打印此文】【关闭窗口】 |
|
|
|
|
|
